A simple explicit single step time integration algorithm for structural dynamics

In this article, a new single-step explicit time integration method is developed based on the Newmark approximations for the analysis of various dynamic problems. The newly proposed method is second-order accurate and able to control numerical dissipation through the parameters of the Newmark approximations. Explicitness and order of accuracy of the proposed method are not affected in velocity-dependent problems. Illustrative linear and nonlinear examples are used to verify performances of the proposed method.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

球罐法兰焊缝损坏的特殊修复方法

多晶硅生产工艺中,盛装氯硅烷球罐本体上的法兰焊缝损坏,在无法将设备内部的氯硅烷彻底置换干净的情况下,应用简易制作的活塞杆塞进法兰短接处,起到密封作用,在保证洁净度的前提下,使设备内部与需修复的法兰焊缝处完全隔离,通过动火分析合格后,对损坏的焊缝进行修复,确保了设备的安全运行,同时,对以后处理相类似的问题提供了借鉴。     

Electromagnetic torque detecting for optimization of in-mould electromagnetic stirring in the billet and bloom continuous casting

ABSTRACT

In this paper, an electromagnetic torque device based on the theoretical model was established to determine the optimum frequency accurately and conveniently in billet and bloom continuous casting with in-mould electromagnetic stirring (M-EMS). Magnetic characteristics with M-EMS was investigated by numerical simulation and physical experiment with the application of electromagnetic torque device and gauss meter. In addition, the effects of stirring frequency with M-EMS on macro segregation and equiaxed crystal ratio were compared and analysed for 55SiCr with 150?mm?×?150?mm billet caster and BU with 310?×?360?mm bloom caster by a series of plant trials, respectively. The results showed that maximum magnetic flux density and maximum electromagnetic torque occurred with different frequency and same current in M-EMS, and central equiaxed crystal ratio and macro segregation has been significantly improved by optimum frequency with M-EMS.     

核电厂电气设备陶瓷部件受风生飞射物的冲击破坏

为研究沿海台风中的风生飞射物对核电厂电气设备的冲击破坏，以核电厂户外高压电气设备的陶瓷绝缘材料为研究对象，基于LS-DYNA和HyperMesh，分析陶瓷部件在小球和钢管打击下的破坏情况。结果表明：在受到钢管垂直打击时，陶瓷部件很容易发生破坏；在受到小球冲击时，陶瓷部件局部表面发生破坏。进一步计算得到小球对陶瓷部件的临界破坏冲击速度，可为后续设计和研究提供参考。     

钢包包衬侵蚀对内衬温度和钢水温降的影响

为了研究包衬侵蚀对钢水温降的影响规律,通过ANSYS有限元软件以及ParaMesh网格随移技术建立了考虑包衬侵蚀的钢包传热计算模型,研究并分析了包衬侵蚀对包衬及钢水温度的影响规律。结果表明,包衬侵蚀对包衬温度影响较大,在相邻两个修包周期内,包衬侵蚀造成渣线和包壁的包衬内部(工作层与永久层交界处)温差为14～114 K;包衬侵蚀导致包壳外表面温度升高,包壳向外散热增加,与此同时,包衬受侵蚀变薄,蓄热减少,两者同时作用导致包衬侵蚀对钢水温降影响不大,最高不超过1 K,在实际生产中可以适当地忽略钢包侵蚀对钢水温降的影响。     

一种人工情绪模型及其电商计算实验应用

针对电子商务顾客购物人工系统的计算实验研究，提出一种基于状态类比假说的人工情绪模型，给出了情绪的产生、增强、衰落和消失过程的描述方法，研究了外部刺激、情感强度和内部驱动力的计算方法，并进行了模拟分析。基于此人工情绪模型，构建了电商顾客购物的情绪-行为影响关系模型；将其应用于电商顾客购物的计算实验分析。结果表明，该人工情绪模型能较好地应用于电商复杂人工系统顾客购物的计算实验。     

非全日制研究生线上线下混合式教学模式研究 ——以《现代电气控制技术》为例

随着教育信息化技术的发展，线上线下混合式教学模式已成为一种趋势。为了解决非全日制研究生课堂教学召集困难、效果不佳等问题，提出了基于“互联网＋虚拟仿真技术”的线上线下混合式教学模式。本文以控制工程专业学位研究生为例，结合《现代电气控制技术》课程，探讨了线上线下混合式教学实现途径、师生互动方法、项目驱动案例教学法以及电气控制系统虚拟仿真实验平台的构建方法，切实提升非全日制研究生的培养质量。     

三维颗粒物质的能量最小化模拟方法

颗粒物质是大量宏观颗粒的集合,广泛存在于自然界,日常生活和工业生产中.颗粒物质的运动表现出非常复杂的现象,如堵塞(jamming)等.颗粒物质体系的定量研究仍是一个巨大的挑战.本文采用能量最小化方法对颗粒物质进行准静态模拟.对一些典型的非线性优化方法,如共轭梯度法,拟牛顿法等,通过预条件来提高这些方法的效率.这些预条件方法基于颗粒体系的几何结构和能量函数来构建.通过对一些典型的准静态过程,如压缩和剪切试验的数值模拟,观察到对三维颗粒体系,预条件方法可以有40%左右的效率提升.